Filter By:

  • Show More Brands
  • Show Fewer Brands

Power Meters

PowerTap G3 Hub Cap Removal Tool
$9.99
- Allows rider to update firmware in G3 PowerCap. - Allows rider to change the hub’s CR2032 battery. - Used for the removal of the G3 PowerCap. - Removes the G3 PowerTap cap to update the firmware or change the hub’s CR2032 battery.
Quarq Battery Cover Red/Elsa/Riken
$39.00
Quarq's Battery Cover replaces your lost or damaged one. It's water-tight, made of aluminum, and works with Quark's Elsa, Riken, and Red 22 power meters (sold separately).
PowerTap Bluetooth Smart Dual Speed/Cadence Sensor
$44.99
PowerTap's Bluetooth Smart Dual Speed/Cadence Sensor gives you the ability to monitor your speed and cadence with your favorite Bluetooth-compatible device. It's sleek and easy to mount on your frame.
CycleOps ANT+ Speed or Cadence Sensor
$49.99
The CycleOps ANT+ Speed or Cadence Sensor accurately tracks your speed and cadence and is used along with a power meter or with an ANT+-compatible cycling computer (power meters and ANT+ computers sold separately). This unit easily attaches on the frame next to your left crankarm and rear wheel to monitor and display your cadence or speed on your cycling computer of choice.
PowerTap PowerCal Dual ANT+/BLE
$69.99
The PowerCal is the world’s first-ever power meter calculated from heart rate. At the time of its release, it was an incredible innovation combining two important training metrics: heart rate and power. And after all these years, the PowerCal remains as one of Powertap's most popular products, and for good reason—athletes of all kinds trust it ride after ride. - First-ever power meter calculated from heart rate. - Most affordable way to begin power training. - Bluetooth Smart or ANT+ compatible. - Signal Transmission: Bluetooth Smart (Cycling Power Service, Heart Rate Service, Device Info Service) or ANT+ (2.4 GHz) - Operational Temperature: 0-40C/32-103F - Battery Type: CR2032 - Battery Life: 400 Operational Hours (Bluetooth); 600 Operational Hours (ANT+) - The PowerCal is not a waterproof device and should not be submerged in water - PowerCal BLE is compatible exclusively with the PowerTap mobile application on iPhone 4S or higher. - PowerCal ANT+ is compatible with android and iPhone/iPad devices with use of appropriate ANT+ adapter key - PowerCal ANT+ is not compatible with cervos (little yellow computer) or older grey indoor cycle consoles.
Sigma Sport Rox GPS 11.0 Set
$259.99
The ROX GPS 11.0 Set contains an R2 DUO COMBO speed and cadence sensor and an R1 DUO heart rate transmitter to take your training to the next level. Connect with sensors and power meters via ANT+. Transfer data to smart phones and tablets via Bluetooth Smart and the SIGMA LINK app. The new Strava live segments, GPS track navigation, sport profiles, and many more features are guaranteed to make the ROX GPS 11.0 the ideal training tool for the most demanding cyclists. Bike functions: - Current speed (kmh/mph) - Average speed - Maximum speed - Current vs. average speed comparison - Distance - Training time - Duration - Calories - Clock (12/24h) - Date - Cadence - Average cadence - Maximum cadence - Average expansion - Average expansion uphill - Average expansion downhill Temperature functions: - Current temperature - Minimum temperature - Maximum temperature Altitude measurement functions: - Altitude - Incline (%) - Rate of ascent in m/min - Altitude profile graph - Altitude uphill - Maximum altitude - Distance up hill - Training time uphill - Average speed uphill - Average rate of ascent - Maximum rate of ascent - Distance downhill - Training time downhill - Average speed downhill - Average rate of descent - Maximum rate of descent - Average slope downhill - Maximum slope downhill Navigation functions: - Time to destination - Estimate time of arrival (ETA) - Distance to destination - Direction - Track view Lap functions: - Manual or automatic laps - Number of laps - Time in lap - Distance in lap - Average speed in lap - Calories in lap - Average altitude in lap - Maximum altitude in lap - Elevation gain in lap - Elevation loss in lap - Average incline in lap - Average decline in lap - Average rate of ascent in lap - Average rate of descent in lap - Average balance n lap - Average power in lap - Maximum power in lap - Normalized power (NP) in lap - Normalized power (NP) in last lap - Average cadence in lap - Maximum cadence in lap - Average heart rate in lap - Maximum heart rate in lap - Pedaling time in lap - Pedaling index in lap - List of laps - Average balance in automatic lap - Average power in last lap - Maximum power in lap Power functions: - Balance - 3 sec average balance - 10 sec average balance - 30 sec average balance - Average balance - Pedal smoothness - Power - Power in % FTP - Average power - 3 sec average power - 10 sec average power - 30 sec average power - Intensity Factor (IF) - Maximum power - Power in KJ - Normalized Power (NP) - Watt/kg power ratio - Power zones - Torque effectiveness - Power target zone Heart rate functions: - Heart rate - Average heart rate - Maximum heart rate - Minimum heart rate - % HR max. - Average % of HR max - Zone bars (heart rate/CAD/SPD) graph - Intensity zones (graph) - Heart rate (graph) Miscellaneous: - STRAVA live segments - ANT+ - Configuration of custom training programs - SRAM eTap - Shimano Di2 - Digital three-axis compass - Barometric altitude measurement - Sports profiles (incl. customizable training views) - Waypoints with custom text - Up to 100 hours log capacity - Backlight - Water tight in accordance with IPX7 - Graphic data evaluation in the DATA CENTER - GPS accuracy indicator - Battery capacity (in %) - Di2 battery status - Expansion - Di2 front gear - Di2 gear ratio - Di2 gears - Di2 rear gear
Specialized Power Cranks - Shimano 105 Upgrade Kit
$425.00 - $429.99
Whether you're looking to take your training to the next level or you simply want a better way to measure energy expenditure, a power meter is your best bet. And the Power Cranks 105 Upgrade Kit are no exception. With our lightweight power sensors on a Shimano 105 crankarm, it's the perfect way to enter the power meter game. The development of Power Cranks began with our Human Performance Team looking at riders in realistic scenarios on the bike. Historically, power meters have been validated by two different methods—one is by measuring the produced torque by applying a static, linear load to a crankarm or chainring, while the second uses a power generating motor to pedal the bike. Well, cycling is neither static nor linear, and humans apply power much differently than a machine. So, we found that neither of these methods answers the 'real-world' accuracy question. To get the best test for accuracy, in all types of riding scenarios, we built our own cycling treadmill, the WinMill, to measure power output to a known truth. This new benchmark lets us evaluate accuracy under all riding conditions—seated versus standing, various power and cadence levels, different weights, and a myriad of gear. This data acquisition process is our gold-standard for testing power meters, and through our testing and external validation from the Locomotion Lab in Boulder, Colorado, Power Cranks have been proven to have the highest accuracy in real-world scenarios (+/- 1.5%). The Power Cranks are also easy to live with, with class-leading temperature compensation firmware and waterproof enclosures. Calibration is only required during seasonal-type fluctuations in temperature, and the included wrench makes battery swaps a breeze. - +/- 1.5% real-world accuracy tested on the WinMill and validated by the Locomotion Lab in Boulder, CO. - Works with ANT+ and Bluetooth devices. - Easy set-up and diagnostics with the Specialized Power app. (iOS and Android versions available). - Shimano 5800 generation 105 left-side power measurement. - Right crankarm and spider NOT included. - Available in 170-175mm crankarm lengths.
Specialized Power Cranks - Shimano Ultegra Upgrade Kit
$525.00
Whether you're looking to take your training to the next level or you simply want a better way to measure energy expenditure, a power meter is your best bet. And the Power Cranks Ultegra Upgrade Kit are no exception. With our lightweight power sensors on a Shimano Ultegra crankarm, it's the perfect way to enter the power meter game. The development of Power Cranks began with our Human Performance Team looking at riders in realistic scenarios on the bike. Historically, power meters have been validated by two different methods—one is by measuring the produced torque by applying a static, linear load to a crankarm or chainring, while the second uses a power generating motor to pedal the bike. Well, cycling is neither static nor linear, and humans apply power much differently than a machine. So, we found that neither of these methods answers the 'real-world' accuracy question. To get the best test for accuracy, in all types of riding scenarios, we built our own cycling treadmill, the WinMill, to measure power output to a known truth. This new benchmark lets us evaluate accuracy under all riding conditions—seated versus standing, various power and cadence levels, different weights, and a myriad of gear. This data acquisition process is our gold-standard for testing power meters, and through our testing and external validation from the Locomotion Lab in Boulder, Colorado, Power Cranks have been proven to have the highest accuracy in real-world scenarios (+/- 1.5%). The Power Cranks are also easy to live with, with class-leading temperature compensation firmware and waterproof enclosures. Calibration is only required during seasonal-type fluctuations in temperature, and the included wrench makes battery swaps a breeze. - +/- 1.5% real-world accuracy tested on the WinMill and validated by the Locomotion Lab in Boulder, CO. - Works with ANT+ and Bluetooth® devices. - Easy set-up and diagnostics with the Specialized Power app. (iOS and Android versions available). - Shimano 8000 generation Ultegra left-side power measurement. - Right crankarm and spider NOT included. - Available in 170-175mm crankarm lengths.
Stages Cycling FSA Energy 386EVO
$529.99
This Stages Power product adds power to FSA Energy BB386EVO cranksets and FSA SL-K Light 2014 and newer carbon drive side cranks. 386EVO specific bottom brackets and adapters solid separately. For more information about the FSA BB386EVO benefits see the FSA website. - Accuracy: ± 2% - Weight: Only adds 20gr to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Stages Support section - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibiity: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling FSA Energy BB30
$529.99
The Stages Power meter is mounted to FSA's hollow forged Energy alloy non-drive crank arm. Please note that the Energy BB30 version has across the board compatibility with FSA and Vision BB30 models. - Accuracy: ± 2% - Weight: Only adds 20 grams to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in our Support section - Crank Compatibility: FSA BB30 cranks; 2014 model MegaExo cranks and newer - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibility: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling FSA Energy MegaExo
$529.99
The Stages Power meter is mounted to FSA's hollow forged Energy alloy non-drive crank arm. The Energy MegaEXO model fits a variety of FSA MegaEXO road cranksets including alloy MegaEXO cranks 2014 and newer and carbon MegaEXO cranks 2008 and newer (SL-K Light, K-Force Light, etc). It is not compatible with triple cranksets or the FSA Omega MegaEXO (which uses a smaller spindle diameter). - Accuracy: ± 2% - Weight: Only adds 20gr to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in our Support section - Crank Compatibility: FSA BB30 cranks; 2014 model MegaExo cranks and newer - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibiity: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling Shimano 105 5700
$529.99
The Shimano 105 5700 Stages Power meter replaces the non-drive crank arm for existing 105 model cranks. Riders looking to add power to their existing crank need only select crank length. The Stages Power meter for 105 fits all styles of 105 cranksets, including: compact and standard. Silver and black finishes are available. This Shimano 5700 Stages Power meter is compatible with all Shimano Hollowtech II road drivetrains. - Accuracy: ± 2% - Weight: Only adds 20 grams to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Stages Support section - Crank Compatibility: All Shimano Hollowtech II road cranks - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibiity: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling Shimano 105 5800
$529.99
The Stages Power meter is built on to a non-drive FC-5800 crank arm specifically to pair with Shimano's 105 5800 crank. This Stages Power meter is slimmer, and up to 28% lower profile than their original meter. It's sleeker by way of a 17% reduction in frontal area, and Stages also made it stronger. The housing design increases the strength of the battery door and housing connection by 200%t over the previous design. This Shimano 5800 Stages Power meter is compatible with all Shimano Hollowtech II road drivetrains. - Accuracy: ± 2% - Weight: Only adds 20 grams to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in our Support section - Crank Compatibility: All Shimano Hollowtech II road cranks - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibiity: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling Cannondale Hollowgram Si
$579.99
This Stages Power meter is built on to a non-drive Cannondale Si crank arm specifically to pair with Cannondale's Hollowgram Si crank — 2014 or newer. The Stages Power meter will also mate to the Hollowgram SISL2 model crank. This Stages Power meter is slimmer and up to 28% lower profile than their original meter. It's also sleeker, with a 17-percent reduction in frontal area, and they've made it stronger. The housing design increases the strength of the battery door and housing connection by 200-percent over the previous design. - Accuracy: ± 2% - Weight: Only adds 20gr to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Stages Support section - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibility: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling Shimano Ultegra 6700
$579.99
The Stages Power meter is built on to a non-drive FC-6700 crank arm specifically to pair with Shimano's Ultegra 6700 crank. This Stages Power meter is slimmer, and up to 28% lower profile than the original meter. It's sleeker by way of a 17% reduction in frontal area, and Stages also made it stronger. The new housing design increases the strength of the battery door and housing connection by 200% over the previous design. This Shimano Ultegra 6700 Stages Power meter is compatible with all Shimano Hollowtech II road drivetrains. - Accuracy: ± 2% - Power meter housing: new low profile design, with new door interface - Weight: Only adds 20g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Support section - Device Compatibility: ANT+, Bluetooth Smart Ready Software - Compatibility: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling Shimano Ultegra 6800
$579.99
The Stages Power meter is built on to a non-drive FC-6800 crank arm specifically to pair with Shimano's Ultegra 6800 crank. The new Stages Power meter is slimmer, and up to 28% lower profile than the original meter. It's sleeker by way of a 17% reduction in frontal area, and they've also made it stronger. The new housing design increases the strength of the battery door and housing connection by 200% over the previous design. This Shimano Ultegra 6800 Stages Power meter is compatible with all Shimano Hollowtech II road drivetrains. - Accuracy: ± 2% - Power meter housing: new low profile design, with new door interface - Weight: Only adds 20g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Support section - Device Compatibility: ANT+, Bluetooth Smart Ready Software - Compatibility: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling Shimano XT M785
$579.99
The Shimano XT M785 Stages Power meter is a left crank arm plus power meter replacement and fits all Shimano M780/785 model (triple/double) cranks. Riders only need to select the crank length of your existing crank arm. The Stages Power meter fits all XT triple and double cranksets. - Accuracy: ± 2% - Weight: Only adds 20gr to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Stages Support section - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibiity: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling Shimano XT M8000
$579.99
For the dirt heads out there, Stages offers a power meter as a non-drive crank arm for existing Shimano XT M8000 (Single/Double/Triple) cranks. The new Stages Power meter is slimmer, and up to 28% lower profile than the original meter. It's sleeker by way of a 17% reduction in frontal area, and they've also made it stronger. The new housing design increases the strength of the battery door and housing connection by 200% over the previous design. - Accuracy: ± 2% - Power meter housing: new low profile design, with new door interface - Weight: Only adds 20g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Stages Support section - Device Compatibility: ANT+, Bluetooth Smart Ready Software - Compatibility: Training Peaks, Strava, Garmin Training Center and others
Race Face CINCH Power Meter Spindle
$599.99
The CINCH Power Meter gives you the tool to train for the Enduro and XC glory you truly deserve. Protected in your BB Shell, the CINCH Power Meter not only gives you the advantage you need to gauge your training and push your boundaries, but it does it with the compatibility and performance you have come to expect from CINCH. Thanks to the adaptable spindle, you can pick your poison from NEXT SL G4 to Turbine R cranks, and with the Race Face CINCH App and both ANT+ and Bluetooth, you can hook it up to your favorite head unit and be on your way to the wattage cottage in no time. - Power Accuracy +/- 2% - Cadence & pedal efficiency data - Dual Bluetooth low energy technology / ANT+ for head unit compatibility - Battery life over 400h & USB rechargeable - Utilizing CINCH for 1x or 2x configurations - Cinch Power Meter App for iPhone or Android - Just 65g more than standard 134mm mountain spindle
Stages Cycling Carbon for FSA 386EVO
$629.99
The Stages Power meter is built to the proprietary Stages Power carbon left crank arm. The full carbon fiber Stages Power meter and crank arm is directly compatible (no additional components needed) with 386 EVO drive side cranks. It can be retrofit to many SRAM and Truvativ BB30 drive side cranks using one of the Stages 30mm Spindles (sold separately). - Accuracy: ± 2% - Weight: Only adds 20g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 - 2500 - Cadence range (rpm): 20 - 220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Stages Support section - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibiity: Training Peaks, Strava, Garmin Training Center and others * This Stages Power meter will not fit SRAM's GXP bottom bracket interface.
Stages Cycling FSA SL-K BB30
$629.99
The Stages Power meter paired with FSA's SL-K Light BB30 left crank arm. Please note that the SL-K Light BB30 version has across the board compatibility with FSA and Vision BB30 models. This Stages Power meter is slimmer, and up to 28% lower profile than their original meter. It's sleeker by way of a 17% reduction in frontal area, and Stages also made it stronger. The housing design increases the strength of the battery door and housing connection by 200% over the previous design. - Accuracy: ± 2% - Weight: Only adds 20 grams to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Stages Support section - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibiity: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling Shimano Dura-Ace 9000
$649.99
The Stages Power meter is built on to a non-drive FC-9000 crank arm specifically to pair with Shimano's Dura-Ace 9000 crank. This meter has been proven, as it was ridden to victory in the 2015 Tour de France by Team Sky. This Stages Power meter is slimmer, and up to 28% lower profile than our original meter. It's sleeker by way of a 17% reduction in frontal area, and Stages also made it stronger. The new housing design increases the strength of the battery door and housing connection by 200% over the previous design. This Shimano Dura-Ace 9000 Stages Power meter is compatible with all Shimano Hollowtech II road drivetrains. - Accuracy: ± 2% - Power meter housing: new low profile design, with new door interface - Weight: Only adds 20g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in our Support section - Device Compatibility: ANT+, Bluetooth Smart Ready Software Compatibility: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling Shimano Dura-Ace Track 7710
$649.99
The Dura-Ace Track FC-7710 is Stages Power meter offering for Track Riders. It replaces the non-drive crank arm for existing Dura-Ace FC-7710 track cranksets. The Stages Power meter fits all Dura-Ace FC-7710 cranksets. Riders looking to add power to their existing crank need only to select crank length. - Accuracy: ± 2% - Weight: Only adds 20 grams to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 10-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Stages Support section - Crank Compatibility: Shimano Octalink cranks - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibiity: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling Shimano DXR MX71
$649.99
The BMX specific DXR MX71 Stages Power meter replaces a non-drive crank arm for existing Shimano DXR MX71 model cranks. Riders looking to add power to their existing crank need only select length — the Stages Power meter fits all current generation DXR cranksets. - Accuracy: ± 2% - Weight: Only adds 20 grams to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Stages Support section - Crank Compatibility: Shimano Saint and DXR Hollowtech II cranks - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibiity: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling Shimano Saint M820
$649.99
The downhill specific Saint M820/825 Stages Power replaces non-drive crank arm on existing Shimano Saint M820/825 model cranks. The Stages Power meter fits all Saint cranksets. Riders need only to select crank arm length. - Accuracy: ± 2% - Weight: Only adds 20 grams to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Stages Support section - Crank Compatibility: Shimano Saint and DXR Hollowtech II cranks - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibiity: Training Peaks, Strava, Garmin Training Center and others
Stages Cycling Shimano XTR M9000 Race/M9020 Trail
$649.99
For the dirt addicts out there, Stages offers a power meter available as a non-drive crank arm for the Shimano M9000/M9020 model cranks. Riders looking to add power to their existing crank need only select the applicable XTR model and length to fit their needs. The M9000 Race version is built from two expertly forged pieces that are bonded together, with a reduced Q-factor of 158mm. XTR Race will only be available in 170mm and 175mm configurations to start. The M9020 Trail version is a more traditional 3D forged piece (much like the current M980 model) but with the new aesthetic. M9020 will be available in 5mm increments from 165mm to 180mm, with a Q-factor of 168mm. The new Stages Power meter is slimmer, and up to 28% lower profile than the Stages original meter. It's sleeker by way of a 17% reduction in frontal area, and we've also made it stronger. The new housing design increases the strength of the battery door and housing connection by 200% over the previous design. - Accuracy: ± 2% - Power meter housing: new low profile design, with new door interface - Weight: Only adds 20g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Stages Support section - Device Compatibility: ANT+, Bluetooth Smart Ready Software Compatibility: Training Peaks, - Strava, Garmin Training Center and others
Stages Cycling Shimano XTR M980/M985
$649.99
The Shimano XTR M980 and M985 Stages Power meter replaces either their Shimano M980 (triple/double) or M985 model (double) left crank arm. Add power to existing cranksets, by selecting the crank length of your existing crank arm, as well as the matching crank model to account for a differences in the arms' offset. - Accuracy: ± 2% - Weight: Only adds 20gr to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Support section - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibiity: Training Peaks, Strava, Garmin Training Center and others
Quarq DZero Power Meter Spider
$679.00
When Quarq set out to build their next-generation power meter, they wanted to build the best-performing power meter for every facet of cycling and triathlon, and for riders at every level. Like its Quarq brethren, the DZero measures power in the heart of the bicycle—the crankset spider, scientifically proven to be the place for the most accurate measurement. With a new measurement circuit, revised strain gauge design, improved accuracy throughout the pedal stroke and software advances built into the Qalvin App, the DZero Spider represents the state of the art in power meter technology Meet the Quarq DZero Power Meter Spider—the DZero in spider form. Ready to pair with any Quarq Prime Power ready cranksets. - Bluetooth low energy technology and ANT+ wireless data transfer - 10K Temperature Compensation - Battery: CR2032, 200-hour battery life, change without tools - OmniCal: swap chainrings without affecting accuracy - 2-year warranty - IPX7 waterproof rating - Accuracy within 1.5%
Quarq DZero Aluminum Power Meter Chassis BB30
$779.00
When Quarq set out to build their next-generation power meter, they wanted to build the best-performing power meter for every facet of cycling and triathlon, and for riders at every level. Like its Quarq brethren, the new DZero measures power in the heart of the bicycle — the crankset spider, scientifically proven to be the place for the most accurate measurement. With a new measurement circuit, revised strain gauge design, improved accuracy throughout the pedal stroke and software advances built into the Qalvin App, the DZero represents the state-of-the-art in power meter technology As Quarq’s next generation of power meters, the DZero combines 10 years of technology advances with new features such as dual Bluetooth low energy and ANT+ wireless data transfer, the new Qalvin BLE app. - 10K temperature compensation: Eliminates variables caused by heat and cold to provide an unwavering record of your performance through all conditions - Built to last: Features an IPX7 waterproof rating - Bluetooth low energy technology and ANT+ wireless data transfer - Battery: CR2032, 200-hour battery life, change without tools - OmniCal: swap chainrings without affecting accuracy - 2-year warranty - IPX7 waterproof rating - Accuracy within 1.5% - Bottom Bracket Compatibility: BB30 - Forged aluminum models do not work with BBright or BB386EVO bottom brackets
Quarq DZero Aluminum Power Meter GXP Crankset
$779.00
When Quarq set out to build their next-generation power meter, they wanted to build the best-performing power meter for every facet of cycling and triathlon, and for riders at every level. Like its Quarq brethren, the new DZero measures power in the heart of the bicycle—the crankset spider, scientifically proven to be the place for the most accurate measurement. With a new measurement circuit, revised strain gauge design, improved accuracy throughout the pedal stroke and software advances built into the Qalvin App, the DZero represents the state of the art in power meter technology As Quarq’s next generation of power meters, the DZero combines 10 years of technology advances with new features such as dual Bluetooth low energy and ANT+ wireless data transfer, the new Qalvin BLE app. - 10K temperature compensation: Eliminates variables caused by heat and cold to provide an unwavering record of your performance through all conditions - Built to last: Features an IPX7 waterproof rating - Bluetooth low energy technology and ANT+ wireless data transfer - Battery: CR2032, 200-hour battery life, change without tools - OmniCal: swap chainrings without affecting accuracy. - 2-year warranty - IPX7 waterproof rating - Accuracy within 1.5% - Bottom Bracket Compatibility: SRAM GXP - Forged aluminum models do not work with BBright or BB386EVO bottom brackets
Page 1 of 2 Next page